The most popular supplier of special protective co

2022-08-01
  • Detail

Suzhou on-site custom measurement Youjia machine tool special protective cover supplier

Suzhou on-site custom measurement Youjia machine tool special protective cover supplier nmzmuooe machine tool steel plate protective cover section number is very important to its proportion, weight and operating characteristics. Each single section shall be as long as possible, so as to reduce the number of sections and reduce the cost. In general, the ratio of tension to minimum compression shall be between 3:1 and 5:1. The machine tool steel plate protective cover is well sealed, which can prevent iron filings, coolant and accidental accidents of tools. 1. it is durable, stable in operation, low in noise and beautiful in appearance. 2. the steel plate protective cover is suitable for high-speed machine tool guide rail protection, which is stable and free of vibration and noise. 3. the steel plate protective cover device not only protects the service life of the protective plate, but also ensures the precision of the machine tool. 4. each section of the steel plate protective cover shall be opened and retracted in parallel at the same time, so that it can run freely. 5. the steel plate protective cover will not make the protective plate disjointed and has impact sound, which is beautiful and improves the service life of the protective plate. 6. a layer of stainless steel cover plate is added on the basis of the original sealant strip to prevent iron filings from burning the rubber strip into the rail surface and damaging the guide rail. Introduction to flexible organ type protective cover: organ protective cover

Suzhou door-to-door custom measurement Youjia machine tool special protective cover supplier

Junxing steel plate protective cover, as the name suggests, its structural design is mainly to prevent personal safety and the machine tool's own protection. In terms of personal safety, human body cannot directly contact the dangerous area of the machine tool In order to prevent the operators from being injured due to the wrong operation of the hands and feet of the government, scientific research institutions, R & D and enterprise collaborative innovation government industry university research cooperation docking mechanism, the width and side length of each section of the steel guide rail protective cover shall not be less than 15mm The steel plate protective cover is installed on the worktable of the cast iron test piece until the test piece is damaged Implement non-contact connection with the machine tool guide rail of the protected part There are no metal parts in the protective cover. During operation, there is no need to worry that the protective cover will loose and fall off after being powered on for 1 hour every week, causing unnecessary wear or damage to the machine tool

Suzhou home custom measurement Youjia machine tool special protective cover supplier

steel plate guide rail protective cover is made of high-quality mm thick steel plate by cold pressing, and can also be stainless steel according to requirements. Special surface polishing will increase its value. We can provide corresponding guide rail protection types for all types of machine tools (horizontal, vertical, China's building materials and products combustion performance classification standard tilt, horizontal). According to the different running speed and guide rail, the protective cover structure we developed is also different. We are equipped with polyurethane or brass sliders when the running speed is below 10m/min. We are equipped with rollers under the medium speed of 30m/min. In addition, a buffer system is required between the drive plate, the chip scraping plate and the chip suction plate. The purpose of the slider buffer system is to reduce collision, noise and friction

machine tool steel plate protective cover is a traditional form of machine tool guide rail protection. In this field, the steel plate protective cover is widely used, which plays an effective role in preventing the entry of chips and other sharp objects. Through certain structural measures and appropriate scraping plates, the penetration of coolant can also be effectively reduced. The steel plate guide rail protective cover can meet the increasing requirements of modern machine tools for high technology, correct installation position and high running speed

the protective cover of the machine tool is used to protect the guide rail of the machine tool. It can protect the internal hard guide rail, linear guide rail, ball screw or transmission rack of the machine tool from external corrosion and damage. It has many kinds, including: organ protective cover and steel plate protective cover, which are used on the guide rail; There are also screw protective covers used on the screw, including round, square and polygon. These methods are different. There are steel wire support type and suture type. There are also roller shutter type protective covers and armor protective covers, etc

can be used to protect the lead screw, polished rod, column, spindle and other circular rotating cylinders. It can be used horizontally or vertically. For horizontal use, it is recommended to use plastic or aluminum support rings to keep a certain uniform distance between the inner cavity of the shield and the screw rod, so as to prolong the service life. When the stretching length is large, a metal ring can be added to each compromise to improve the stability of the shield. Metal flange is usually used for connection or fixed end, and hoop type can also be selected

Copyright © 2011 JIN SHI